bigcoupe.com

??? Not my car or parts to sell, I inquired about buying some parts from this car

completed auto to 5sp conversion on 81 633csi, I have only driven it around circle driveway so do not know how its gonna feel on the road but a question; It has oem diff, believe its 3:45 and only one rear wheel spins/drives (r/r) and that makes it useless to drive if any snow on ground/driveway. Co...

try again, 12V direct to external fuel pump, nothing, the old "tap" on it with handle end of screwdriver and YIPPIE!, she starts buzzing, and pumping fuel, guess I woke her up from a long long nap. Car starts, just need to disconnect and re position gas pedal linkage at firewall so to get ...

looking for steering column cruise control stalk

so on final phase of auto to 5sp conversion, 1981 633csi, 43K original miles, drove it onto lift, been almost 2 yrs not started. Have jumped necessary wires at auto plug in, engine started on "starting fluid spray" but getting no fuel to engine. Have "jumped" relay, hear intank p...

all set in instrument cluster parts, thanks to all that replied

im Interested in the exhaust down pipes only, no cat. Let me know if that’s something you’ll part with Best, Hector Hector, The down pipes and cat are one piece, or are you asking to cut off the cat and send just the down pipes? Curious minds have to know!! https://www.realoem.com/bmw/enUS/showpart...

looking for cruise control lever on steering column. Is car still in TC area?
Karl, UP Mich

looking for E24 instrument cluster for "parts", do not need speedo or tach, just housing, actually looking for the plastic panel strip that on auto's shows gear selected, but I am doing conversion to 5sp so need blank strip so I am not looking at "N,D, 1,2,3, L," etc

BTW, this project is a Auto to 5sp conversion, so a little slow go, Forum feedback always a big help

kept looking, thinking, looking some more. I ended up loosening the top nut on rubber mount located on right rear on trans, which is connected to the rear trans mount, also loosened the rear trans mount to the underbody, and shifted the rear of trans to the right side approx 1/4", as the rear m...

thank you for info, going to be great help. Also looking for instrument cluster for manual trans car, only need the upper black out panel strip that has the letters indicating which gear in for an automatic (P,N,D,1,2, or L) OEM strip is NLA ( 62111360543) or guess I will take auto panel out, make n...

will be easy to do, was thinking same but wondering why it is this way, will wait a while to see if other thoughts

yes meant center line of driveshaft, front to rear is off at center support to the (vehicle) right approx 1/8' to maybe 1/4", so guess that would be the "preload" ??, similar to the 2mm preload forward, on the center bearing as you tighten it to mount point,,,

just installed driveshaft on '81 633csi, with new center support bearing. I notice the driveshaft is maybe 1/8" to 1/4" inch off center ( f to r) at the center support bearing, i.e., run straight edge for complete drive shaft, front to rear and center is slightly off to (car) right side, i...

finally getting close on conversion from auto to 5sp on '81 633csi, pedal box done,everything underneath done except driveshaft, so next will be back on interior, steering column re install, center console, shifter/ shift plate etc. Question is what will I need to do wiring to make sure I have spark...

I am asking about pressure plate bolts, to be used with or w/ out washers, not asking about Flywheel bolts, all set there
Thank you

thanks for feedback, lock washers on PPlate bolts it is then, w/blue loctite,,,

doing a auto to 5sp changeover, new bolts for flywheel and p/plate. real oem shows bolt only for p/plate, no washers, is that correct? and I see two suggested torque setting for the harder replacement bolt, 22-26 or I read a post stating 36???

looking for 1981 E24 cruise control stalk, accidently leaned on mine and broke it today, any help appreciated

f/s; NEW nitro ball/accum ATE#34002-10.0515-0515.3, lists at $159.95, sell for $85 plus shipping obo
located UP Michigan

not the same, I have the auto console plate, I have a manual shift plate for it, but it is in poor condition, "cig" burns, etc and they are two diff P/N's also,,,thanks for input

do not need boot, I need center console piece that has cut out for shift boot and window switches P/N 51161859982

WTB; center console gear shift cover (manual trans), p/n 51 16 1 859 982 doing a auto to manual trans conversion and need center console shift lever/boot cover, boot not the issue, need the console piece the boot attaches to, looking, looking, part is nla new. PM with what you may have, pic would be...

in search of shifter mount plate p/n 25111205386 and selector rod p/n 25111204438 (147mm)
pm or email if anyone may have, include price and contact info please