bigcoupe.com

UPDATE It started!. the reason for the no start condition was simple but not obvious. My ecu has the miller performance war chip. I took the ecu out to make a small global adjustment to the timing curve at my tuner. The tuner, after making the change by mistake, had changed the rev limiter to 0 rpm...

The original relays (which had been working fine for 3 years) that I used on both the main and fuel were plugged in and behaved the same as the new ones and the used and new main both got hot. part numbers are as per the parts catalog.

Jpr

bump

Help. was running fine but now it cranks but no start. No changes have been made. changed, CTS, FP relay, Main Relay, cleaned AFM. Only clue is main relay was worm/hot even on the unswitched position. even with no key in the ignition, if you present the main relay to the socket, it goes click. batte...

looking for both left and right fog lights on m635.

thanks

Jpr

I have a Miller MAF kit so I dont have the AFM arrangement anymore. The main bypass screw (the one you adjust 8 turns from fully closed) is the one that, at the moment, makes no change on the idle (no matter the position). I have disconnected the hose from the intake plenum and the idle control slid...

Hi, Anybody familiar with the pin-out of the Bosch 055 (euro M635csi) pin-out? looking to make a loom to shoot for a stand-alone ECU.

Thanks

Jpr

Replaced the CTS and no effect.....What to try next?

No, not yet. Stock timing. could coolant temp sensor affect the idle speed?

Took the car for smoke testing. They found no leaks. However, I can still place a plastic bag over the airbox opening (I have removed the snorkel) and the engine still runs!!. Not smoothly as without it but the idle does not go down. Again, Throttle plates are all closed (the stop screws are all wit...

Yes, that would take care of the upper one, but how about the lower one?

Agreed, the question is however, give all that has been done, where can that large of a vacuum leak be?

Have high idle condition in a M88, Here is what I've done so far: Engine is newly rebuilt New o rings in metering needles New o rings in bypass screw Fully flowed injectors with new o rings Adjusted bypass, throttle blades, bypass screw per manual Slide valve works well. fully closed at working temp...

The throttle linkage in the M635csi has two push rods looking at each other towards the rear of the engine (the front has only one with the springs) these two are so close together that I cant remove the nuts holding each let alone remove the push rod itself. any idea how it is done?

TIA
Jpr

Still looking......

Jpr

Thanks Ray. Im in 3553 NW 79 Ave. Miami, 33122. You can send the pictures to [email protected]

Thanks

Jose Puig

Im looking to buy a driver side front manual seat base.

Thanks

Jpr

I would surely recommend the coating. Look for a local source for the process, it is not proprietary and many powder coaters do it. The reduction in under-hood temps will keep all the other components younger.

Jpr

Don't be discouraged in your search for coilovers. Ground Control can help you our and GAZ seems to make a very finished product. The smaller diameter spring will give you the best clearance for your tires and wheels and the adjustability will allow you to tailor the handling characteristics. Every ...

sent my engine to a reputable builder with the fuel rail and the injectors and they lost it while working on the head. Need one to finish the build.Please let me know if you have one available.

Thanks

Jpr

So, nobody has done this?

Jpr

I have used shocks like the Bilstein sports and others thru the years and the quality of the damping performance is not as good as good coilover setup. having replaced the Koni shocks in a 944 turbo with the 28 series coilover brought about much better body control and less harshness. The Bilstein i...

replacing the shocks in my car and not want to use the usual Bilstein sport solution. Want to have the option of controlling the shock settings and corner weights with coilovers but not want to lower the car much (maybe 1/2"). Has anyone used the GAZ brand? I have heard horror stories of BC and...

Hi,

Trying to find a source of the mounting dowel to re-enforce the steering box mounting on the M635. My contact is no longer replying to my request. is there anyone who is still supplying this?

Thanks

Jpr

thanks Ron, the Nogaro silver is the color on the window side of the of the chrome strip on the molding right?

Thanks

Jpr