Search found 43 matches

by Tazzarti
Mon Jun 06, 2022 9:53 pm
Forum: Cars and Parts for sale
Topic: 1981 633 csi, Parts Car
Replies: 2
Views: 1031

Re: 1981 633 csi

Hi Guys, I hope bumping is allowed. I had one member PM me, but seems to have not logged in since. Now that covid restrictions are a bit less at the border I was hoping to open this sale back up. Id like to give this community the chance before I put it in a few more public places. I unfortunately w...
by Tazzarti
Tue Sep 07, 2021 11:18 pm
Forum: Cars and Parts for sale
Topic: 1981 633 csi, Parts Car
Replies: 2
Views: 1031

1981 633 csi, Parts Car

Hi Everybody, The rear suspension has finally pushed through the body on my old scrappy 633. It’s a 1981 (type 1) that was heavily modified sometime in the 80s or 90s. I’m looking to sell it for the good parts (see list below). Unfortunately because of my living situation I cannot part out the car. ...
by Tazzarti
Mon Oct 26, 2020 2:05 am
Forum: Cars and Parts wanted
Topic: First gen rear push rods
Replies: 2
Views: 1638

Re: First gen rear push rods

635sharknose wrote: Sun Oct 25, 2020 7:05 pm Don't know how it is in Canada, but here in Europe they are only 29 EURO at the BMW dealer.
Ill def give them a shout. Since covid it does take longer than a month for stuff to get here from Germany.

Thanks
by Tazzarti
Sun Oct 25, 2020 6:49 pm
Forum: Cars and Parts wanted
Topic: First gen rear push rods
Replies: 2
Views: 1638

First gen rear push rods

Hi Im looking for two of the push rods that attach the rear axle carrier to the frame for a first gen e24 ('81 633 in Canada). The BMW part number is 33333628172 seen here: https://www.realoem.com/bmw/enUS/showparts?id=5235-USA-01-1981-E24-BMW-633CSi&diagId=33_0189 as number 11. I do see them ne...
by Tazzarti
Fri Jul 31, 2020 2:12 am
Forum: Cars and Parts wanted
Topic: WTB Rear Lower Spring Perch for e28 based Bilsteins
Replies: 3
Views: 2161

WTB Rear Lower Spring Perch for e28 based Bilsteins

I'm putting e28 springs on my 81 633's Bilstein's. The shocks that donated the top hats did not have a removable spring plate. I'm looking just for two metal spring plates for the lower part of the rear shock to hold the rubber perch.

Thanks,
by Tazzarti
Wed Aug 21, 2019 10:32 pm
Forum: Cars and Parts wanted
Topic: Drivers (left) Rear Dust Shield - Pre'82
Replies: 6
Views: 4845

Re: Drivers (left) Rear Dust Shield - Pre'82

Thanks, they have the one for the right side, but not the left. Im not sure its the exact same part, but maybe it can be altered enough to fit.
by Tazzarti
Tue Aug 20, 2019 9:41 pm
Forum: Cars and Parts wanted
Topic: Drivers (left) Rear Dust Shield - Pre'82
Replies: 6
Views: 4845

Drivers (left) Rear Dust Shield - Pre'82

Im looking for part 34211104548. The shop wont put my rear end back together after a wheel bearing replacement since my old one is too rusty apparently. I cant find a retailer that actually has one. Didnt think these would be so rare :S https://www.realoem.com/bmw/enUS/showparts?id=5235-USA-01-1981-...
by Tazzarti
Thu Mar 21, 2019 3:18 am
Forum: Engine - Mechanical - Electrical
Topic: Rough Idle/Loss of power under load [M30b32]
Replies: 8
Views: 5311

Re: Rough Idle/Loss of power under load [M30b32]

Hoping to bump; I checked the throttle position sensor, and something seems to be off. https://imgur.com/pZQRD2O https://imgur.com/pZQRD2O In the electrical diagram it says that pin 3 is closed and 2 is open. But on my car this is reversed. This reverse pin out seems to be the case for the cars from...
by Tazzarti
Thu Mar 21, 2019 2:51 am
Forum: Engine - Mechanical - Electrical
Topic: e12 based hvac question (fan control)
Replies: 12
Views: 8153

Re: e12 based hvac question (fan control)

Image
https://imgur.com/H5hI4LC

Hi guys, I cant comment on the diagnosis, but this is the diagram from the BMW north america electrical troubleshooting manual. For a 1977 630. Hope this helps.

-Not sure how to embed the photo :S
by Tazzarti
Tue Nov 20, 2018 10:48 pm
Forum: Cars and Parts wanted
Topic: Rear seatbelt assembly and Fuel Sending unit
Replies: 3
Views: 2539

Re: Rear seatbelt assembly and Fuel Sending unit

Tazzarti, got a fuel sending unit for you =D> This was removed from my '80 in the hopes it would "cure" the erratic fuel gauge response, alas the problem lies in the gauge itself :-? I would presume with virtual certainty that it's still functioning, although I have no way of proving that...
by Tazzarti
Tue Nov 20, 2018 1:43 am
Forum: Cars and Parts wanted
Topic: Rear seatbelt assembly and Fuel Sending unit
Replies: 3
Views: 2539

Rear seatbelt assembly and Fuel Sending unit

Hi, Im looking for two parts; 1. Rear Passenger Seatbelt assembly, someone decided to cut a seatbelt :S 72111875228 http://www.realoem.com/bmw/enUS/showparts?id=5235-USA-01-1981-E24-BMW-633CSi&diagId=72_0135 2. Fuel Level Sending Unit 16121153050 http://www.realoem.com/bmw/enUS/showparts?id=5235...
by Tazzarti
Tue Oct 09, 2018 3:42 am
Forum: Cars and Parts for sale
Topic: acquired a nice PARTS car. NC. 1980 633csi auto. need anything?
Replies: 58
Views: 73589

Re: acquired a nice PARTS car. NC. 1980 633csi auto. need anything?

I Pm'd you , but do you have any of the following:

1. Injectors
2. Fuel level sender
3. Rear passenger seatbelt assembly
4. Glove box latch
5. center console vent cover

Thanks,
by Tazzarti
Tue Jul 10, 2018 1:25 am
Forum: Cars and Parts wanted
Topic: WTB: Thermostat housing
Replies: 3
Views: 26525

Re: WTB: Thermostat housing

hornhospital wrote: Mon Jul 09, 2018 3:11 am Pelican Parts has it:

https://www.pelicanparts.com/cgi-bin/ks ... 1531710959
Thanks, not a bad price either
by Tazzarti
Mon Jul 09, 2018 11:52 am
Forum: Engine - Mechanical - Electrical
Topic: Rough Idle/Loss of power under load [M30b32]
Replies: 8
Views: 5311

Re: Rough Idle/Loss of power under load [M30b32]

just to be sure, the conventional way of numbering cylinders is from #1 at the front (ancillary belt) end of the engine to #6 at the rear (bulkhead/firewall) end of the engine. In most cases fuel enters the fuel rail near the #6 position and leaves (via the FPR) at the #1 end. There should be a cop...
by Tazzarti
Mon Jul 09, 2018 1:42 am
Forum: Cars and Parts wanted
Topic: WTB: Thermostat housing
Replies: 3
Views: 26525

WTB: Thermostat housing

Looking for a thermostat housing:

11531710959
https://www.realoem.com/bmw/enUS/showpa ... Id=11_0710


Thanks,
by Tazzarti
Mon Jul 09, 2018 1:34 am
Forum: Engine - Mechanical - Electrical
Topic: Rough Idle/Loss of power under load [M30b32]
Replies: 8
Views: 5311

Re: Rough Idle/Loss of power under load [M30b32]

if the cylinders with low pressure were neighbouring cylinders, it might be that the head gasket was starting to blow, cylinder to cylinder, rather than just worn rings or something. The compression figures may have become worse with use regardless of cause, so check them again, If the idle is terr...
by Tazzarti
Thu Jun 28, 2018 10:11 pm
Forum: Engine - Mechanical - Electrical
Topic: Rough Idle/Loss of power under load [M30b32]
Replies: 8
Views: 5311

Re: Rough Idle/Loss of power under load [M30b32]

I wish it could be that easy, but I do not have a cat anymore actually :P straight pipe up front, Billy Boat performance exhaust in the rear (so just a muffler)
by Tazzarti
Thu Jun 28, 2018 1:50 am
Forum: Engine - Mechanical - Electrical
Topic: Rough Idle/Loss of power under load [M30b32]
Replies: 8
Views: 5311

Rough Idle/Loss of power under load [M30b32]

hi guys, I have a 1981 633, and Ive been trying to get the engine to run smoothly for 3 years (as well as rebuild the rest of the car) but at this point Im stuck. Ill go over what ive done and the timeline as it may happen that something I fixed early on has now become defective since and Im overloo...
by Tazzarti
Tue May 08, 2018 1:03 am
Forum: Suspension - Steering - Brakes
Topic: 1981 Front stabalizer removal
Replies: 6
Views: 4710

Re: 1981 Front stabalizer removal

I ground down the cheap wrench I had and it was fairly easy to remove. Found out my my connecting rod nuts were basically welded on with rust. Needless to say Im now waiting for the ST Suspension 52015 kit to arrive.

Thanks everyone for your input!
by Tazzarti
Mon Apr 30, 2018 12:58 am
Forum: Suspension - Steering - Brakes
Topic: 1981 Front stabalizer removal
Replies: 6
Views: 4710

Re: 1981 Front stabalizer removal

Thank you all for the feedback. My car is far away and I drive my tools in so I didnt have a ring wrench when i looked at her last week. This week a bought ring wrench, and the 17 mm wrench in the tool kit is a 17-15 open end that would not fit. With the wrench i bought I was able to get one side of...
by Tazzarti
Wed Apr 25, 2018 12:35 am
Forum: Suspension - Steering - Brakes
Topic: 1981 Front stabalizer removal
Replies: 6
Views: 4710

1981 Front stabalizer removal

I just want to replace the rubber mounts on my front stabilizer, but I have no clue how to access the bolt. There is a diagram on page 31-15 of the repair manual but all they say is to undo the bolt. The problem is that its sandwiched behind the bushing and under a frame rail. I wasnt able to even f...
by Tazzarti
Wed Nov 01, 2017 12:45 pm
Forum: Cars and Parts wanted
Topic: 1981 Window motors and a regulator
Replies: 1
Views: 51429

1981 Window motors and a regulator

Hi Im looking for the front two window motors, as well as the front right window regulator from the old style 633 (1981 here). The part numbers are as follows: Front left motor 51331369249 superseded by 51331375247 front right motor 51331369250 superseded by 51331375248 front right regulator 5133192...
by Tazzarti
Wed Jun 21, 2017 9:19 pm
Forum: Cars and Parts wanted
Topic: WTB Radiator
Replies: 9
Views: 8504

Re: WTB Radiator

Tazzarti - your car has the early style / design radiator for E24 fitted to 9/82. From 9/82 there was a different design. If you have a manual gearbox your rad part number is 17111121296 if your car was produced prior to 9/82. Check out REALOEM website with your VIN number. Great reference. I'm gue...
by Tazzarti
Wed Jun 21, 2017 1:42 am
Forum: Cars and Parts wanted
Topic: WTB Radiator
Replies: 9
Views: 8504

Re: WTB Radiator

dwcains wrote:I'm afraid I don't know the answer to that question, but I'd guess someone at FCP does. Sometimes the aftermarket parts will replace more than one OEM part number.
Okay thanks, Ill keep digging
by Tazzarti
Tue Jun 20, 2017 11:39 pm
Forum: Cars and Parts for sale
Topic: Continuation of a trailer full of parts
Replies: 24
Views: 15121

Re: Continuation of a trailer full of parts

Is there still a radiator up for grabs? Yes but I think shipping to Canada will cost a few $$. I am willing to ship there but if you have a US address to ship to it would be easier on you. Thats true, someone informed me that there is a cheap one of FCp euro (didnt show up when shopping for an 81) ...