bigcoupe.com

Bump...Still in need

I have to chime in and also give Kos kudos for his great work and attention to detail! What a great asset for our community to have someone do this for just the right finishing touches on our cars!

Bump...anyone know what this is? Thanks!

I am in the process of putting my car back together from the PO, and there are a bunch of unmarked wires that I need to find out where they go. Here is a connection (blue and brown wire), that is coming from the same wire loom as one of the white connectors from the back of the instrument cluster. A...

Looking for rear tail light frames that don't have any rust or pitting. Also need the rubber to go along with them. Build date is 11/84 and is a 1985 model year.

Thanks!
Jack

PM sent. Thanks!

Thanks.

I replaced both the speed and reference sensors, and still nothing. I'll check the grounds again, but already went over them a couple of times to check. I am getting power to the fuel pump and the fuel tank gauge is showing an accurate reading. This is why this is so maddening for me!

Ok...the replacement of the crankcase sensors didn't help. This is what I did and what I found. Any advice from here? 1. Pin 4 at the Motronic control unit (black/yellow wire) coming from the starter and I made sure there is continuity between the starter end and the ECU end of the wire. 2. I check...

Ok...the replacement of the crankcase sensors didn't help. This is what I did and what I found. Any advice from here? 1. Pin 4 at the Motronic control unit (black/yellow wire) coming from the starter and I made sure there is continuity between the starter end and the ECU end of the wire. 2. I checke...

Thanks Brucey. Mine is a 11/84 build date. I order 2 Bosch sensors, so I should be good. Thanks again!

So I went into the sensors a little further, and saw that the PO must have removed the actual connector at the top end of the wire and just plugged the 3 flat prongs into the harness. Needless to say, I ordered new sensors and will retest once they are installed. I just don't trust what was done pre...

you should check that you have a 'start signal' at the ECU (pin 4 IIRC) when you are cranking. Without that, the ECU won't make sparks, won't close the fuel pump relay. Can't be sure it is that, but it is one thing on the list... hth cheers I tested the ECU #4 pin and I have almost 12V (I think my ...

Ok, here is another "won't start" post... My car is in the middle of a restoration and nearing completion. I am putting the engine back together and want to do a test start to be sure everything is working and I want to do this before I put the rest of the car together. The engine cranks w...

Awesome! Thank you to you both for this! This is exactly what I needed. I owe you both :)

Bump?

if the engine won't stop on the key, your problems are certainly not confined to the starter circuit. If you don't have it, I would suggest that you get a copy of the relevant ETM, eg. from the wedophones/downloads link. cheers Thanks. I think that was the way he set it up. I wound up switching all...

I need some assistance here... I bought my car a couple years ago, and the PO had installed a push button start since the ignition switch in the column was not working. While he installed the button, he cut and wiped out any history of how the solenoid and alternator were wired. With the push button...

Nice to see a guy sweating the details! =D> It makes all the difference. More pix of engine bay, please. I'll post some this week since I have the week off and will be doing more work in the engine bay. Car is a work in progress (like all the rest) and came back from paint a few weeks back. Slowly ...

Looks great Dean! Isn't it amazing what the little details do to our cars!

Who rebuilt your compressor? Mine is in need of it. Thanks!

PM Sent...thanks!

PM Sent. Thanks!

Here are the new decals! Kos did an amazing job!! He even cut the emissions decal the same way the original was cut so that no one can tamper with it once it is on.

I need to replace my center kidney grilles with one that are not dented. Anyone out there that has a good set? PM me if you have them. Also need other parts...

Hey all! Just wanted to see if anyone out there has this? I also need the transistors and plat the completes the enclosure on the passenger side of the evaporator box. Any help or sources for this would be greatly appreciated so I can get my Heat and AC back up and running. Thanks for looking.