Reserve fuel tank - Spare Wheel
Moderators: GRNSHRK, ron, bfons
Reserve fuel tank - Spare Wheel
Inserted my (new to me) Reserve fuel tank into my spare wheel, and the treaded bolt is just shy of the metal disk, I can't get the wing bolt attached to secure the Reserve fuel tank/ Tyre. Any help appreciated! The OEM Alloy is late highline 195 TR 415 CH.
- Attachments
-
- photo.JPG (34.67 KiB) Viewed 11743 times
-
- photo[1].JPG (34.37 KiB) Viewed 11743 times
________________________________
1989 - 635CSI Highline - Lach Silver
1989 - 635CSI Highline - Lach Silver
Try the tank in first, then the tire.
Jay
'88 M6, Red/Tan
My NEW Website https://www.jaysbmwparts.com/
'88 M6, Red/Tan
My NEW Website https://www.jaysbmwparts.com/
Thanks for the reply, I think it's the metal disk, RealOEM references three different types. I know these tanks are rare outside Germany. maybe someone will chime in who has one.
- Attachments
-
- DSC01710_zpsfa5c0a53.jpg (118.09 KiB) Viewed 11699 times
________________________________
1989 - 635CSI Highline - Lach Silver
1989 - 635CSI Highline - Lach Silver
I mean put the tank into the spare tire well, and put the tire on top, facing finish side up.
Jay
'88 M6, Red/Tan
My NEW Website https://www.jaysbmwparts.com/
'88 M6, Red/Tan
My NEW Website https://www.jaysbmwparts.com/
Could the spare tank fit OVER (rather than under) the spare tire hold down?
Or is the hold down bolt longer with the spare tank? Did the spare tank come with the car and the hold down or did you add it?
Or is the hold down bolt longer with the spare tank? Did the spare tank come with the car and the hold down or did you add it?
Sansouci
84 E24 633Csi Auto, Bronzit/PearlBeige 6997510
93 E32 740il M60 Auto, Alpenweis/Ultramarine
60 528i M30 5-speed Green/Beige (crushed)
71 240Z 4-speed White/Blue (rusty & sold)
65 396 Chevelle 4-speed, Marina Blue/Black (stolen)
84 E24 633Csi Auto, Bronzit/PearlBeige 6997510
93 E32 740il M60 Auto, Alpenweis/Ultramarine
60 528i M30 5-speed Green/Beige (crushed)
71 240Z 4-speed White/Blue (rusty & sold)
65 396 Chevelle 4-speed, Marina Blue/Black (stolen)
- DRPM635CSi
- Posts: 280
- Joined: Thu Jul 09, 2015 6:50 am
- Location: Perth, Australia
- Contact:
Re: Reserve fuel tank - Spare Wheel
The spare wheel must go in upside down when you have one of these. The instructions even state so. If you fit the fuel tank first and then put the spare wheel over it, the retaining washer/bolt will only hold down the spare wheel from moving around, not the fuel can underneath, so you'd be hearing the canister going clunk-clunk-clunk and getting all scratched up as it smacks around against the inside of the wheel rim as you brake and corner.
https://www.dropbox.com/s/5oumb44kptquq ... .pdf?raw=1
The reason your retaining washer doesn't allow the threaded bolt to protrude through far enough to get the wing nut on is because a special washer is needed in conjunction with the fuel canister. It's part number 82-11-9-413-201 and is long since NLA. I have one but have been unable to find anyone who can reproduce it economically. It's a special profile shape with a deep recess for the wing nut to reach the threaded rod of the hold down bolt. It also has an unusually small Ø80mm OD to perfectly match the centre-bore of the fuel canister and sits perfectly flat & flush. It is also completely circular without a slot interuption like some of the wheel hold down plates.
Probably your best option to find a retaining washer that looks genuine is to scour some wreckers and see if you can find a plate from other model cars with a deep enough centre recess to expose the thread for the wingnut if it were turned down to Ø80mm on a lathe and then get that done.
On this subject... does anyone know the part numbers for the twin retainer washer plates for the spare wheel hold down assembly employed in the M635CSi? The twin plates that sandwiched the flimsy little piece of driftwood chipboard used to maintain a flat boot floor above the spare wheel in the M635CSi exclusively? The top one of these plates could be turned down to Ø80mm OD to produce a workable OE looking retaining washer for the auxiliary fuel canister in place of the unobtainable 82-11-9-413-201.
https://www.dropbox.com/s/5oumb44kptquq ... .pdf?raw=1
The reason your retaining washer doesn't allow the threaded bolt to protrude through far enough to get the wing nut on is because a special washer is needed in conjunction with the fuel canister. It's part number 82-11-9-413-201 and is long since NLA. I have one but have been unable to find anyone who can reproduce it economically. It's a special profile shape with a deep recess for the wing nut to reach the threaded rod of the hold down bolt. It also has an unusually small Ø80mm OD to perfectly match the centre-bore of the fuel canister and sits perfectly flat & flush. It is also completely circular without a slot interuption like some of the wheel hold down plates.
Probably your best option to find a retaining washer that looks genuine is to scour some wreckers and see if you can find a plate from other model cars with a deep enough centre recess to expose the thread for the wingnut if it were turned down to Ø80mm on a lathe and then get that done.
On this subject... does anyone know the part numbers for the twin retainer washer plates for the spare wheel hold down assembly employed in the M635CSi? The twin plates that sandwiched the flimsy little piece of driftwood chipboard used to maintain a flat boot floor above the spare wheel in the M635CSi exclusively? The top one of these plates could be turned down to Ø80mm OD to produce a workable OE looking retaining washer for the auxiliary fuel canister in place of the unobtainable 82-11-9-413-201.
Re: Reserve fuel tank - Spare Wheel
thanks DRPM635CSi, great research work, thanks for the PDF.
________________________________
1989 - 635CSI Highline - Lach Silver
1989 - 635CSI Highline - Lach Silver
-
- Posts: 22
- Joined: Thu Oct 27, 2016 11:53 am
- Location: Bixby Ok (Tulsa)
Re: Reserve fuel tank - Spare Wheel
Thanks DRPM635CSi, I've been looking for that info. Can you post a few pictures of the hardware and washers used?
Steve
1984 325E, 745I
1988 635CSI
1989 325I
1989 325I sold
1983 528E both Sold
1984 325E, 745I
1988 635CSI
1989 325I
1989 325I sold
1983 528E both Sold
- DRPM635CSi
- Posts: 280
- Joined: Thu Jul 09, 2015 6:50 am
- Location: Perth, Australia
- Contact:
Re: Reserve fuel tank - Spare Wheel
As requested:
82-11-9-413-201
The M635CSi washers I want to know the part numbers for:
82-11-9-413-201
The M635CSi washers I want to know the part numbers for: