I was cleaning the carpet in my shark today and knocked the accelerator pedal loose from its lower hinge. I pulled the carpet back and noticed the mount for the hinge is completely rusted.
There wasn't a post about this that I could find -- has anybody else encountered this issue? If so, what's the easiest way to reattach the pedal to the floor? Glad it broke when I was working on the car, not when I was driving!
The floor area seemed pretty damp, so I assume I have a leaky windshield gasket or something else that's letting water in. Gotta investigate that too.
Any thoughts on fixing this?
-Michael
633CSi rusty accelerator pedal mount by Michael Downes, on Flickr
633CSi rusty accelerator pedal mount by Michael Downes, on Flickr
Rusty accelerator pedal mount
Moderators: GRNSHRK, ron, bfons
Re: Rusty accelerator pedal mount
UPDATE: It looks like this is the right part to fix my issue. BMW apparently didn't offer it as a stand-alone part, so that's why I couldn't find any references to it in the parts diagram. I'll grind the old one down and weld in this new one when it gets here.
https://www.ebay.com/itm/BMW-E30-Faceli ... 4361396940
https://www.ebay.com/itm/BMW-E30-Faceli ... 4361396940
Re: Rusty accelerator pedal mount
If you want to repair properly and prevent reoccurance then ......
Remove drivers seat , lift carpet , remove sound deadening , remove all of that detritus in the photo and get back to bare metal. Once the metal has been exposed examine it carefully to establish it's remaining condition and strength . If rotten cut out and weld in new fresh metal, prep and paint and then reweld fulcrum bracket for throttle pedal.
When stripped down look for water ingress up under bulkhead /scuttle or glaring rust holes on floor forward of and to the side of the throttle pedal area .....
If sun roof fitted check initially drains are not blocked ,remove trim cover on lower A piller , locate sunroof drain pipe and extend and exit it through the manufactured hole under car .
Looking at your photos , I'd predict that just forward of the area exposed a " welcome to E24 ownership " surprise awaits you ...
I wish you good luck .
Don
Remove drivers seat , lift carpet , remove sound deadening , remove all of that detritus in the photo and get back to bare metal. Once the metal has been exposed examine it carefully to establish it's remaining condition and strength . If rotten cut out and weld in new fresh metal, prep and paint and then reweld fulcrum bracket for throttle pedal.
When stripped down look for water ingress up under bulkhead /scuttle or glaring rust holes on floor forward of and to the side of the throttle pedal area .....
If sun roof fitted check initially drains are not blocked ,remove trim cover on lower A piller , locate sunroof drain pipe and extend and exit it through the manufactured hole under car .
Looking at your photos , I'd predict that just forward of the area exposed a " welcome to E24 ownership " surprise awaits you ...
I wish you good luck .
Don
1981 635 series 1
-
- Bigcoupe Contributor
- Posts: 323
- Joined: Wed Sep 10, 2014 12:08 am
- Location: Arden, NC 28704
Re: Rusty accelerator pedal mount
Michael, one possibility for water entry is through the main wire harness, located near the fire wall. Our cars should have a rain/water defector mounted on the underside of the hood. People have been creative and cover the area with an aluminum foil baking pan.
The sealant often dries out and allows water through. Re-seal it and it should fix your problem. A water deflector would help as well!
See photos of the BMW factory solution. Roger
The sealant often dries out and allows water through. Re-seal it and it should fix your problem. A water deflector would help as well!
See photos of the BMW factory solution. Roger
89 635CSiA (11/88 build)
AlpineWeiss II (218)/Natur(0200)
87 L6 635CSI Sold
87 MB 560SL Sold
AlpineWeiss II (218)/Natur(0200)
87 L6 635CSI Sold
87 MB 560SL Sold
Re: Rusty accelerator pedal mount
Thanks Don and rhanley. I definitely don't have the deflector, but I'll see if I can track one down. The leak will take some time to track down. This e24 is much less rusty than the previous 77 630CSi that I had. The floorboards were totally shot on that one. So far I haven't discovered too many surprises on this one. Fingers crossed!