This throttle cable is NLA from BMW so the only option is to make one.
Looking for the following cable end crimps:-
I've tried 6 cable suppliers in the UK and Germany and all have said they don't make them!!
Someone, somewhere must, so would be most appreciated if forum members could do a search local to them.
TIA.
PS There could be an interesting reward!
End crimps for RHD M635 throttle cable.
Moderators: GRNSHRK, ron, bfons
End crimps for RHD M635 throttle cable.
They are ALWAYS rustier than you thought!!!!!!
'85 M #228
'87 M #367
'88 High line.
'10 X5
‘84 Alfasud 1.5 ti
'85 M #228
'87 M #367
'88 High line.
'10 X5
‘84 Alfasud 1.5 ti
-
- Posts: 797
- Joined: Wed Sep 01, 2010 3:29 pm
- Location: Broomfield, CO
Re: End crimps for RHD M635 throttle cable.
PN - 35412225340 Shows NLA...
Good luck
Good luck
- 12 535i
- 92 325ic
- 92 325ic
-
- Platinum Member
- Posts: 1659
- Joined: Mon Jul 16, 2007 2:58 pm
- Location: Cheltenham, U.K.
Re: End crimps for RHD M635 throttle cable.
Stupid question time - is there any way the crimps can be removed and reused? I've got a couple of spares from a cooking 635 if cannibalism (of parts) is of interest! I'm going to need to make a cable that stretches all the way from the throttle, round the bulkhead, past the exhaust manifold to the bypass valve on the supercharger, so I'll be needing to develop some cable fabrication skills.
"Most of it necessary; all of it enjoyable." LJKS
'84 635CSi, dogleg...itbs and supercharger????? Eaton Mess
'84 635CSi, dogleg...itbs and supercharger????? Eaton Mess
- hornhospital
- Platinum Member
- Posts: 2940
- Joined: Sun Jul 11, 2010 6:46 pm
- Location: Silverhill, AL
- Contact:
Re: End crimps for RHD M635 throttle cable.
You can't "uncrimp" the ends, but you _may_ be able to split the fitting with a hacksaw or mototool and cutoff wheel, remove the cable, and lengthen by silver soldering, then reattach the end by the same method. You need to be skilled at silver soldering/brazing or all you'll do is ruin the cable by overheating.
Ken Kanne
'84 633CSi "Sylvia"; '85 635CSi "Katja";'85 325e "Hazel Ann"; '95 M3 "Ashlyn"
'84 633CSi "Sylvia"; '85 635CSi "Katja";'85 325e "Hazel Ann"; '95 M3 "Ashlyn"
-
- Platinum Member
- Posts: 3320
- Joined: Thu Sep 28, 2006 9:28 pm
- Location: scottsdale, arizona
- Contact:
Re: End crimps for RHD M635 throttle cable.
You might try drilling out the existing cable. Also cut the fitting back and fit a tube over it and solder on. Silver soldering can be done with a Bernzomatic torch. I think you get the idea. Mainly fitting a new tube over the old one. Once that is done, you can fit another tube to proper size in the new tube and then crimp your `cable. If you think about it it is not difficult.
81 Euro 635 M90 with motronic. Currently under a complete nut and bolt restoration. Pictures at
flickr.com/photos/bertsphotos.
flickr.com/photos/bertsphotos.
Re: End crimps for RHD M635 throttle cable.
Have you tried Venhill or some of the other custom cable manufacturers?
https://www.venhill.co.uk
The other thing of course, both of those crimps look like they started off round and straight, there could be the option to get a batch made?
Are the LHD cables NLA?
https://www.venhill.co.uk
The other thing of course, both of those crimps look like they started off round and straight, there could be the option to get a batch made?
Are the LHD cables NLA?
Re: End crimps for RHD M635 throttle cable.
Have emailed. Waiting for a reply.
One crimp is straight and we have manufactured one.
The other hook-shaped crimp we are investigating manufacturing options.
https://www.realoem.com/bmw/enUS/showpa ... Id=35_0121
https://www.realoem.com/bmw/enUS/showpa ... Id=35_0125
Different cable but might be worth trying.Still available from BMW.
Thanks for the tips Ken. I did a lot of silver soldering cables when I was involved with an autogyro manufacturer.hornhospital wrote: ↑Sat Jul 04, 2020 1:05 am You can't "uncrimp" the ends, but you _may_ be able to split the fitting with a hacksaw or mototool and cutoff wheel, remove the cable, and lengthen by silver soldering, then reattach the end by the same method. You need to be skilled at silver soldering/brazing or all you'll do is ruin the cable by overheating.
Thanks Bert it might come to that.bpoliakoff wrote: ↑Sat Jul 04, 2020 1:51 am You might try drilling out the existing cable. Also cut the fitting back and fit a tube over it and solder on. Silver soldering can be done with a Bernzomatic torch. I think you get the idea. Mainly fitting a new tube over the old one. Once that is done, you can fit another tube to proper size in the new tube and then crimp your `cable. If you think about it it is not difficult.
They are ALWAYS rustier than you thought!!!!!!
'85 M #228
'87 M #367
'88 High line.
'10 X5
‘84 Alfasud 1.5 ti
'85 M #228
'87 M #367
'88 High line.
'10 X5
‘84 Alfasud 1.5 ti
-
- Platinum Member
- Posts: 3320
- Joined: Thu Sep 28, 2006 9:28 pm
- Location: scottsdale, arizona
- Contact:
Re: End crimps for RHD M635 throttle cable.
Silver soldering can be done with hi silver content plumbing solder or even hobbyist silver solder. It can be flowed out with an old fashioned soldering iron and make a fine connection. Cleanliness, flux and even heat to both surfaces are the key words. If not comfortable with this your local home improvement store will have mini butane torches which will provide more than adequate heat
81 Euro 635 M90 with motronic. Currently under a complete nut and bolt restoration. Pictures at
flickr.com/photos/bertsphotos.
flickr.com/photos/bertsphotos.