I am looking for one front left bumper end cap #10 - #51111869769. Mine is rusting on the inside! The plastic is bulging up in spots and the mounting hardware is MIA. The PO attached them with coat hanger wire....
I'm looking for one in relatively good condition and in original black unpainted plastic with all its hardware intact.
Brian
North American bumper corner wanted
Moderators: GRNSHRK, ron, bfons
North American bumper corner wanted
- Attachments
-
- 51111869769.jpg (87.84 KiB) Viewed 5160 times
01/1987 M6
past Bimmers;
1970 2800CS
1988 325is
1985 325E
past Bimmers;
1970 2800CS
1988 325is
1985 325E
- Hefeweizen
- Posts: 2324
- Joined: Thu Jul 17, 2008 1:24 pm
- Location: Colorado Springs
- Contact:
Re: North American bumper corner wanted
For what year car? I have a couple that are in decent condition that go on pre 87
Rainer
03 330Xi (DD)
85 635CSi (RIP 3 May 19)
80 633CSi (Red Euro, Project)
"If you think a good European mechanic is expensive, try a bad one!"
03 330Xi (DD)
85 635CSi (RIP 3 May 19)
80 633CSi (Red Euro, Project)
"If you think a good European mechanic is expensive, try a bad one!"
Re: North American bumper corner wanted
Sorry, forgot that.
This is for an 01/1987 M6.
This is for an 01/1987 M6.
01/1987 M6
past Bimmers;
1970 2800CS
1988 325is
1985 325E
past Bimmers;
1970 2800CS
1988 325is
1985 325E
- Hefeweizen
- Posts: 2324
- Joined: Thu Jul 17, 2008 1:24 pm
- Location: Colorado Springs
- Contact:
Re: North American bumper corner wanted
Rainer
03 330Xi (DD)
85 635CSi (RIP 3 May 19)
80 633CSi (Red Euro, Project)
"If you think a good European mechanic is expensive, try a bad one!"
03 330Xi (DD)
85 635CSi (RIP 3 May 19)
80 633CSi (Red Euro, Project)
"If you think a good European mechanic is expensive, try a bad one!"
-
- Posts: 212
- Joined: Wed Nov 20, 2013 4:17 pm
- Location: Massachusetts, U.S.
Re: North American bumper corner wanted
I have a full set in black, need some work however
http://bigcoupe.com/phpBB2/viewtopic.php?f=8&t=30973
http://bigcoupe.com/phpBB2/viewtopic.php?f=8&t=30973
- Hefeweizen
- Posts: 2324
- Joined: Thu Jul 17, 2008 1:24 pm
- Location: Colorado Springs
- Contact:
Re: North American bumper corner wanted
I have to say that I find this post rather disturbing,kylefav390 wrote: ↑Fri Jun 21, 2019 9:25 pm I have a full set in black, need some work however
http://bigcoupe.com/phpBB2/viewtopic.php?f=8&t=30973
Rainer
03 330Xi (DD)
85 635CSi (RIP 3 May 19)
80 633CSi (Red Euro, Project)
"If you think a good European mechanic is expensive, try a bad one!"
03 330Xi (DD)
85 635CSi (RIP 3 May 19)
80 633CSi (Red Euro, Project)
"If you think a good European mechanic is expensive, try a bad one!"
-
- Posts: 212
- Joined: Wed Nov 20, 2013 4:17 pm
- Location: Massachusetts, U.S.
Re: North American bumper corner wanted
why is that?Hefeweizen wrote: ↑Sat Jun 22, 2019 12:42 amI have to say that I find this post rather disturbing,kylefav390 wrote: ↑Fri Jun 21, 2019 9:25 pm I have a full set in black, need some work however
http://bigcoupe.com/phpBB2/viewtopic.php?f=8&t=30973
-
- Posts: 64
- Joined: Sat May 03, 2014 5:31 am
- Location: Danville, CA
Re: North American bumper corner wanted
I had my front valance off for a re-spray In October 2016. The shop found that the left front covering was in perfect condition but the right front was rusting on the inside. I located a new covering from BMW and just decided to replace it (my OCD cost me $232). It looks like both the right and left side coverings are now discontinued.
1985 635CSi 5MT Delphin Grey/Pearl Beige
Does a guilt free shark have a feeling of remoras?
Does a guilt free shark have a feeling of remoras?