Parting 1988 635csiA
Moderators: GRNSHRK, ron, bfons
Parting 1988 635csiA
Just picked it up hoping to rehab it, but have since found terminal rust. Silver with grey interior. Air dam is broken but available if you feel like repairing it.
Interior is in very good shape, but has been sitting, so we will need to clean the car out and clean the interior before sending anything out. Would prefer to sell the interior as a set.
RF fender in decent shape, as are the doors, hood, and deck lid. Everything else has rust.
I will list some individual parts of interest below as I remove them from the car and will make notes as they sell.
New Hella (OE) turn signal lenses, $50 each, shipped or $90 for the pair.
Ellipsoids, will ship with wiring harness. I have to assess any tab damage before pricing, but the lenses are good.
Reman driveshaft for 4HP22. $150 plus shipping
Complete stripe kit NIB. Pics and price to come.
Short bumper plastic set. Some repainting, but all in usable shape. Rear bumper has a small crack in the rear right corner, but can be TIGed.
Let me know if you have any specific requests. No pics till after Sandy buggers off.
Interior is in very good shape, but has been sitting, so we will need to clean the car out and clean the interior before sending anything out. Would prefer to sell the interior as a set.
RF fender in decent shape, as are the doors, hood, and deck lid. Everything else has rust.
I will list some individual parts of interest below as I remove them from the car and will make notes as they sell.
New Hella (OE) turn signal lenses, $50 each, shipped or $90 for the pair.
Ellipsoids, will ship with wiring harness. I have to assess any tab damage before pricing, but the lenses are good.
Reman driveshaft for 4HP22. $150 plus shipping
Complete stripe kit NIB. Pics and price to come.
Short bumper plastic set. Some repainting, but all in usable shape. Rear bumper has a small crack in the rear right corner, but can be TIGed.
Let me know if you have any specific requests. No pics till after Sandy buggers off.
Thank you for the kind thoughts. We missed most of the bad storm.Johnyakimo1855 wrote:Would potentially be intereste in front spoiler and all mounting brackets and hardware (mine were bent terribly), Floormats in good condition? Price on both shipped to 78754. Hope your ok up there, thoughts and prayers are with all of ya'll.
Thanks,
John
I will check on the floor mats when I get a chance, probably this weekend.
I'll check on shipping the air dam. Since it's broken, I won't need to get much for it, but mostly have to charge for packing and shipping.
I believe that I may have a complete set of mounting brackets in addition to the ones mounted to the car if you just need those.
- Kelowna635
- Posts: 207
- Joined: Tue Jun 09, 2009 4:53 pm
- Location: Kelowna, BC Canada
Was interested in front air dam.
But I am looking for one piece of it.
Do either of you have the piece that
goes beside the drivers fog light?
Color does not matter. It's the only
thing that's missing on my car.
But I am looking for one piece of it.
Do either of you have the piece that
goes beside the drivers fog light?
Color does not matter. It's the only
thing that's missing on my car.
Tom Masters
TGM Drafting & Design
1988 635csi - Bronzeit - Natur - RIP
1986 635csi - Black - Black - RIP
1979 528i - RIP
1981 320i - Sold
TGM Drafting & Design
1988 635csi - Bronzeit - Natur - RIP
1986 635csi - Black - Black - RIP
1979 528i - RIP
1981 320i - Sold
- Kelowna635
- Posts: 207
- Joined: Tue Jun 09, 2009 4:53 pm
- Location: Kelowna, BC Canada
John,
See attached pic of car, I think they refer to part as "Covering"
I hit a snow bank and blew the spoiler into five pieces.
Lots of epoxy and some plastic reinforcement, it's back together.
Just lost that one part, even went back in spring to find it.
Must be in someones collection of trinkets.
Let me know what you want for it.
Tom
See attached pic of car, I think they refer to part as "Covering"
I hit a snow bank and blew the spoiler into five pieces.
Lots of epoxy and some plastic reinforcement, it's back together.
Just lost that one part, even went back in spring to find it.
Must be in someones collection of trinkets.
Let me know what you want for it.
Tom
- Attachments
-
- Kelowna635 missing part.jpg (168.51 KiB) Viewed 11011 times
Tom Masters
TGM Drafting & Design
1988 635csi - Bronzeit - Natur - RIP
1986 635csi - Black - Black - RIP
1979 528i - RIP
1981 320i - Sold
TGM Drafting & Design
1988 635csi - Bronzeit - Natur - RIP
1986 635csi - Black - Black - RIP
1979 528i - RIP
1981 320i - Sold
I started posting some pictures here:
https://picasaweb.google.com/1019692385 ... directlink
Some of the pics from that are some E32 parts.
I can ship international. I use flat rate boxes to keep the pricing down.
https://picasaweb.google.com/1019692385 ... directlink
Some of the pics from that are some E32 parts.
I can ship international. I use flat rate boxes to keep the pricing down.
Sorry to keep everyone waiting. The garage is currently full of an E32 I'm getting ready to scrap.
I'll be working on the car this weekend, hopefully, so I'll take pictures of everything and see if there are enough people interested in parting out the interior to make it worthwhile to sell separately.
I do have an M30B35 for parts as well.
I'll be working on the car this weekend, hopefully, so I'll take pictures of everything and see if there are enough people interested in parting out the interior to make it worthwhile to sell separately.
I do have an M30B35 for parts as well.
Bringing this post back from the dead. My wife needed ACL reconstruction surgery which seriously delayed this effort.
picture link
Everything in those pictures is available. Car has extended leather. I pulled the vinyl headliner by pulling the glass from the car. Everything is in pretty darn good shape.
Motor is also available, but I did not try to run it due to a rodent chewed harness. Car also has ellipsoids. Rear deck has sunshade. Rear bumper is present but cracked. Front bumper is really corroded under the trim. Air dam is cracked and missing fogs. Nose panel is dented but repairable if yours is trashed. Tails are crap. Late bumper trim is in OK shape. Hood is in decent shape.
Most body panels are rusty. Driver door handle hardware is gone. Many pieces of exterior trim are gone. Rear AC parts are spoken for, but the console is available. Rear seats are gone. Rear window motors are gone. Dash is gone. AC controls are gone. Exhaust is spoken for. Diff is spoken for.
I will cut any steel off the car you need, but a lot of this car has rust.
picture link
Everything in those pictures is available. Car has extended leather. I pulled the vinyl headliner by pulling the glass from the car. Everything is in pretty darn good shape.
Motor is also available, but I did not try to run it due to a rodent chewed harness. Car also has ellipsoids. Rear deck has sunshade. Rear bumper is present but cracked. Front bumper is really corroded under the trim. Air dam is cracked and missing fogs. Nose panel is dented but repairable if yours is trashed. Tails are crap. Late bumper trim is in OK shape. Hood is in decent shape.
Most body panels are rusty. Driver door handle hardware is gone. Many pieces of exterior trim are gone. Rear AC parts are spoken for, but the console is available. Rear seats are gone. Rear window motors are gone. Dash is gone. AC controls are gone. Exhaust is spoken for. Diff is spoken for.
I will cut any steel off the car you need, but a lot of this car has rust.
Last edited by mooseheadm5 on Sat Apr 27, 2013 6:49 pm, edited 1 time in total.
-
- Platinum Member
- Posts: 3320
- Joined: Thu Sep 28, 2006 9:28 pm
- Location: scottsdale, arizona
- Contact:
Re: Interior
I've got people already interested in the front seats and the rear are gone, but if you want the remaining interior as a whole, let me know and I'll go through and verify what I have left.jah_shed wrote:What are you wanting for the complete interior?
- Masked Man
- Platinum Member
- Posts: 1301
- Joined: Sat Jun 28, 2008 5:46 pm
- Location: Los Angeles, CA
That's how I want my Buster to sit!!!
I've gone through hell for it to happen!! Just a nice 1" drop in the front!!
I like the rear to be stock height.
My Buster is Polaris too. Your car is ready for the world!
It sounds like there's a song there?!
I've gone through hell for it to happen!! Just a nice 1" drop in the front!!
I like the rear to be stock height.
My Buster is Polaris too. Your car is ready for the world!
It sounds like there's a song there?!
Hit the apex
in Long Beach, Cal
Buster/'82Euro6 Build Date 9/81
Rosallina/'80 528i Build Date 4/80
in Long Beach, Cal
Buster/'82Euro6 Build Date 9/81
Rosallina/'80 528i Build Date 4/80
Do you still have:
1. ellipsoids
2. fog lamps
3. header panel (with kidney grilles)
4. automatic shit handle
5. deck lid spoiler in decent shape
and if so how much are you looking to have for them plus shipping to Austin?
Will-
1. ellipsoids
2. fog lamps
3. header panel (with kidney grilles)
4. automatic shit handle
5. deck lid spoiler in decent shape
and if so how much are you looking to have for them plus shipping to Austin?
Will-
"letting somebody borrow your car is like letting someone borrow your wife- You'll never know if you'll get it back with a rod thrown in it-"
Ron "Santa Claus" Schluettor
Ron "Santa Claus" Schluettor
- Kelowna635
- Posts: 207
- Joined: Tue Jun 09, 2009 4:53 pm
- Location: Kelowna, BC Canada
Spoiler part
Hi,
Talked to you last fall about that part for my front spoiler.
Just go to first posts on this thread, it will jog your mind, LOL.
I am also in need of a couple of sockets for brake lamps, needs
to have about 3" or more wire attached.
Tom
Talked to you last fall about that part for my front spoiler.
Just go to first posts on this thread, it will jog your mind, LOL.
I am also in need of a couple of sockets for brake lamps, needs
to have about 3" or more wire attached.
Tom
Tom Masters
TGM Drafting & Design
1988 635csi - Bronzeit - Natur - RIP
1986 635csi - Black - Black - RIP
1979 528i - RIP
1981 320i - Sold
TGM Drafting & Design
1988 635csi - Bronzeit - Natur - RIP
1986 635csi - Black - Black - RIP
1979 528i - RIP
1981 320i - Sold
1) Yes, $200 shipped in the USBlack-Out wrote:Do you still have:
1. ellipsoids
2. fog lamps
3. header panel (with kidney grilles)
4. automatic shit handle
5. deck lid spoiler in decent shape
and if so how much are you looking to have for them plus shipping to Austin?
Will-
2) No, they were gone when I got the car
3) Yes, but it is a little bent and so are the kidneys
4) I'll check
5) Nope
Re: Spoiler part
Put it aside for you if you are still interested, but it isn't in great shape as noted before (but may be salvageable.)Kelowna635 wrote:Hi,
Talked to you last fall about that part for my front spoiler.
Just go to first posts on this thread, it will jog your mind, LOL.
I am also in need of a couple of sockets for brake lamps, needs
to have about 3" or more wire attached.
Tom
Can probably help with the lamps.
- Masked Man
- Platinum Member
- Posts: 1301
- Joined: Sat Jun 28, 2008 5:46 pm
- Location: Los Angeles, CA
All the shit handles I've grabbed over the years, have been manuals. ~completely innocent look~Black-Out wrote:Do you still have
...
4. automatic shit handle
...
Will-
Keep the shiny side up
Phillip
Masked Man
85 635CSi Euro
Big Brake Upgrade
Ireland stainless exhaust
Upper & lower control arms
New tie rod kit
85 635CSi Euro
Big Brake Upgrade
Ireland stainless exhaust
Upper & lower control arms
New tie rod kit