Help Support Bigcoupe.com

1983 633csi interior parts/tech help needed

Post in this forum for topics relating to the interior.

Moderators: ron, bfons, GRNSHRK

Post Reply
WhidbeyShark
Posts: 2
Joined: Sat Jan 11, 2020 7:26 pm
Location: Seattle

1983 633csi interior parts/tech help needed

Post by WhidbeyShark » Sat Jan 11, 2020 7:41 pm

I need a replacement drivers side door handle (not the latch for opening the door but the pull handle for closing the door) for my '83 633csi. Mine has cracked near the electric mirror controls. I tried to attach a photo here but not sure this forum has that capability. Can anyone out there help me locate a tan handle? Big thanks!

Also, my fan heater blower fan speed control switch only works on high. Is there a nifty fix for this? If not, I also need to replace this blower switch and would be very grateful for recommendations on where to locate one.

Cheers!

baders
Bigcoupe Contributor
Posts: 1045
Joined: Sun Nov 23, 2014 7:38 am
Location: Perth Australia

Re: 1983 633csi interior parts/tech help needed

Post by baders » Sat Jan 11, 2020 11:09 pm

When posting a reply, look down to the "Attachments" tab. There you can upload appropriately sized images.

Fan heater blower working in high speed only is a well known problem with the transistor and relatively easy fix. Do a search as there's plenty of references.
1986 635csi LOCUTUS / Arktis Blau Metallic / Pearl Beige / S38B36/ Close ratio dogleg 5sp
2002 E46 M3 / Topaz Blau Metallic / Black Nappa / 6 speed SMG software tuned / Bilstein PSS10 Coilovers / CMP RACP reinforcement

WhidbeyShark
Posts: 2
Joined: Sat Jan 11, 2020 7:26 pm
Location: Seattle

Re: 1983 633csi interior parts/tech help needed

Post by WhidbeyShark » Sun Jan 12, 2020 7:38 pm

baders wrote:
Sat Jan 11, 2020 11:09 pm
When posting a reply, look down to the "Attachments" tab. There you can upload appropriately sized images.

Fan heater blower working in high speed only is a well known problem with the transistor and relatively easy fix. Do a search as there's plenty of references.
Thanks for your reply. It took me about 40 minutes to figure out how to gain access and participate in this forum which is to say...I am not terribly savvy when it comes to computers. Can you send me a link or more specific help for this easy fix? Much appreciated!

baders
Bigcoupe Contributor
Posts: 1045
Joined: Sun Nov 23, 2014 7:38 am
Location: Perth Australia

Re: 1983 633csi interior parts/tech help needed

Post by baders » Mon Jan 13, 2020 4:27 am

In this thread look down to Chris Wrights post and a link to an excellent article on this;

viewtopic.php?f=11&t=2465&p=205817&hili ... or#p205817
1986 635csi LOCUTUS / Arktis Blau Metallic / Pearl Beige / S38B36/ Close ratio dogleg 5sp
2002 E46 M3 / Topaz Blau Metallic / Black Nappa / 6 speed SMG software tuned / Bilstein PSS10 Coilovers / CMP RACP reinforcement

songzunhuang
Bigcoupe supporter
Posts: 916
Joined: Fri Aug 14, 2015 10:04 am
Location: Silicon Valley, CA
Contact:

Re: 1983 633csi interior parts/tech help needed

Post by songzunhuang » Fri Jan 24, 2020 5:57 am

Are we sure that he's not talking about this transistor?
This was the problem for my 1984 633csi when the fan would only blow on high. It's easy to get to and an easy fix. The new transistor was less than $3.
Screen Shot 2020-01-23 at 9.53.59 PM.png
Transistor that burns out.
Screen Shot 2020-01-23 at 9.53.59 PM.png (739.5 KiB) Viewed 925 times
I've replaced this twice now. Second time I made more effort to get good heat conduction paste to help with the cooling.
It's been years and seems to be good the 2nd time around.
-----
Song Huang
1984 633CSi
Last 7 of VIN: 6997383

JoelR
Posts: 48
Joined: Sun Mar 09, 2014 4:19 am
Location: DFW (Plano) Texas

Re: 1983 633csi interior parts/tech help needed

Post by JoelR » Sun Feb 09, 2020 8:31 pm

Piggybacking on the blower motor thread:
I replaced that transistor only to have it blow again. So I replaced it again using thermal grease (good thing I bought a 5-pack). I also installed a new Bosch fan motor, since the shaft was not spinning freely on the original one. This time the fan worked on all speeds for a few minutes. Then it went back to working only on full.
Did I get a run of poor quality transistors (2N3771), or is there something else going on here?
1983 633 5-speed Black & Tan
DFW Texas

baders
Bigcoupe Contributor
Posts: 1045
Joined: Sun Nov 23, 2014 7:38 am
Location: Perth Australia

Re: 1983 633csi interior parts/tech help needed

Post by baders » Mon Feb 10, 2020 12:58 am

Make sure you buy from a reputable electronics supplier such as Mouser, RS Components, or Element 14 etc. There are many "knock offs" around on Ebay and such of disputable quality.
1986 635csi LOCUTUS / Arktis Blau Metallic / Pearl Beige / S38B36/ Close ratio dogleg 5sp
2002 E46 M3 / Topaz Blau Metallic / Black Nappa / 6 speed SMG software tuned / Bilstein PSS10 Coilovers / CMP RACP reinforcement

JoelR
Posts: 48
Joined: Sun Mar 09, 2014 4:19 am
Location: DFW (Plano) Texas

Re: 1983 633csi interior parts/tech help needed

Post by JoelR » Sun Mar 29, 2020 2:57 pm

Thank you for that advice! I ordered 2 of these from Mouser, and they were visibly different from my eBay sourced parts. Not only that, the one I put in actually worked! So now I have a spare.

Lessons learned from this fan motor and transistor exercise:
1. Get the transistor from a reputable supply house.
2. Before removing the fans from the shaft, make a careful note not only of how far apart they are from each other and the motor, note the relative rotation of each one relative to the other, since they are balanced together. I failed to note the latter, and I can't run my fan higher than 3/4 speed now.
3. Be very careful with the boiling water technique! Scald burn to my hand set me back $175.
4. Don't press too hard on the fans trying to get them on the new shaft if they have cooled off. I cracked on of mine and had to glue it back together.
5. Given the age of the plastic and the difficulty of getting everything back together, if I had it to do over again, I would just buy the whole fan and motor assembly.
1983 633 5-speed Black & Tan
DFW Texas

Post Reply

Who is online

Users browsing this forum: No registered users and 7 guests